Aluminum is one of the most used metals in today’s society – Aluminium Rail Track in Gauteng it can be found across a number of industries, such as construction and commercial, and in a number of applications, such as beverage cans and appliances. When choosing a manufacturer of aluminium extrusion for supplying the metal that you use in your workplace, however, it is important that you carefully consider which one will be best for your needs.
The manufacturer will begin by removing the aluminium from deep within the earth’s crust (either as bauxite ore or feldspar). Often, the Bayer’s method, Wohler’s method or Hall Heroult method is chosen to remove the metal in its molten form. It is then hardened and moulded into whatever shape the manufacturer desires. When the aluminium is extracted from the earth in its solid form, Aluminum Extrusion Slider it will be passed through a number of mechanical processes that are designed to give the metal its desired shape. These processes include: rolling, drawing, forging, spinning, piercing and extrusion.
Regardless of whether aluminium has been found in its molten or solid form, the manufacturer will then pass it through either a hot working or cold working process to prepare it for their customers. When using the hot working process (the most popular of the two), a billet will be heated to a temperature of over 79 degrees Celsius, which will allow the aluminium to be easily distorted and placed into its desired shape.
The reason for the popularity of the hot working process over the cold working one can be fully realized when you compare aluminium extrusion to squeezing toothpaste out of its tube. It is much easier to extrude the metal when it is malleable, meaning that it must have been heated to a certain temperature.
Finally, the aluminium will pass through an extrusion and drawing process that runs almost parallel to each other. This is the final step in the whole extrusion process and is the step that gives the metal its entire shape. Deep drawing, for example, is used give the metal a cup, conical tapered, cylinder and seamless tube shape. For less curved shapes, Aluminium Structural Framing the drawing process is skipped.
Once you are satisfied with the processes and methods utilized by a potential manufacturer of aluminium extrusions, you can begin submitting your orders with them. If, after your first delivery, you are still satisfied with the manufacturer based on the promptness of the order being filled and the quality of the aluminium that you receive, you can continue the relationship.
Aluminium Rail Track in Gauteng?
High strength aluminium alloys.
The origin of aluminium alloys in aircraft construction started with the first practical all-metal aircraft in 1915 made by Junkers in Germany, of materials said to be `iron and steel'. Steel presented the advantages of a high modulus of elasticity, high proof stress and high tensile strength. Unfortunately these were accompanied by a high specific gravity, almost three times that of the aluminium alloys and about ten times that of plywood. Aircraft designers during the 1930s were therefore forced to use steel in its thinnest forms. To ensure stability against buckling of the thin plate, intricate shapes for spar sections were devised.
In 1909 Alfred Wilm, in Germany, accidentally discovered that an aluminium alloy containing 3.5 per cent copper, 0.5 per cent magnesium and silicon and iron, as unintended impurities, spontaneously hardened after quenching from about 480°C. The patent rights of this material were acquired by Durener Metallwerke who marketed the alloy under the name Duralumin. For half a century this alloy has been used in the wrought heat-treated, naturally aged condition. The improvements in these properties produced by artificial ageing at a raised temperature of, for example, 175°C, were not exploited in the aircraft industry until about 1934.
In addition to the development of duralumin (first used as a main structural material by Junkers in 1917) three other causes contributed to the replacement of steel by aluminium alloys. These were a better understanding of the process of heat treatment, the introduction of extrusions in a wide range of sections and the use of pure aluminium cladding to provide greater resistance to corrosion. By 1938, three groups of aluminium alloys dominated the field of aircraft construction and, in fact, they retain their importance to the present day. The groups are separated by virtue of their chemical composition, to which they owe their capacity for strengthening under heat treatment.
The first group is contained under the general name duralumin having a typical composition of: 4 per cent copper, 0.5 per cent magnesium, 0.5 per cent manganese, 0.3 per cent silicon, 0.2 per cent iron, with the remainder aluminium. The naturally aged version was covered by Air Ministry Specification DTD 18 issued in 1924, while artificially aged duralumin came under Specification DTD 111 in 1929. DTD 111 provided for slight reductions in 0.1 per cent proof stress and tensile strength.
The second group of aluminium alloys differs from duralumin chiefly by the introduction of 1 to 2 per cent of nickel, a high content of magnesium and possible variations in the amounts of copper, silicon and iron. `Y' alloy, the oldest member of the group, has a typical composition of. 4 per cent copper, 2 per cent nickel, 1.5 cent magnesium, the remainder being aluminium and was covered by Specification DTD 58A issued in 1927. Its most important property was its retention of strength at high temperatures, which meant that it was a particularly suitable material for aero engine pistons. Its use in airframe construction has been of a limited nature only. Research by Rolls-Royce and development by High Duty Alloys Ltd produced the `RR' series of alloys. Based on Y alloy, the RR alloys had some of the nickel replaced by iron and the copper reduced. One of the earliest of these alloys, RR56 had approximately half of the 2 per cent nickel replaced by iron, the copper content reduced from 4 to 2 per cent, and was used for forgings and extrusions in aero engines and airframes.
The third and latest group depends upon the inclusion of zinc and magnesium and their high strength. Covered by Specification DTD 363 issued in 1937, these alloys had a nominal composition: 2.5 per cent copper, 5 per cent zinc, 3 per cent magnesium and up to 1 per cent nickel. In modern versions of this alloy nickel has been eliminated and provision made for the addition of chromium and further amounts of manganese.
Aircraft structural aluminium.
Of the three basic structural materials, namely wood, steel and aluminium alloy, only wood is no longer of significance except in laminates for non-structural bulkheads, floorings and furnishings. Most modern aircraft still rely on modified forms of the high strength aerospace aluminium alloys which were introduced during the early part of the 20th century. Steels are used where high strength, high stiffness and wear resistance are required. Other materials, such as titanium and fibre-reinforced composites first used about 1950, are finding expanding uses in airframe construction.
Aluminium Extrusion and Its Advantages
Aluminum doors are once popular in the home building industry. With the changes in architectural taste, however, many people opted for different styles of sliding doors. Nonetheless, even when the interest in this type of door has already declined, it still has various advantages that could not be provided by other types of doors.
For one, aluminum pocket doors are great space savers. They could be used in several instances when space is an issue. For example, a room which could not be fixed with a hinge door could make use of a pocket door. This is the case when there is a permanent obstruction along the pathway where the door swings. Since the door runs along a hidden track and vanishes inside a pocket in the wall, there is no longer a need to open the door fully by swinging. Thus, the door does not require more space before it could be opened. Also, a pocket door could effectively replace a standard door when there is no other way but hide the door inside the walls.
Aluminum sliding doors is also a great alternative to ordinary wood, vinyl or plastic doors. This is because the doors are predicted to capture the future trend in home designing alongside glass and other metals.
There are downsides to using the doors though. For one, these doors could not be used in places where there are extreme temperatures as aluminum tends to adopt to the temperature of its surrounding. This would not help neutralize the heat or the coldness inside a room, for example. Also, aluminum, unlike wood, glass and fiberglass doors, tends not to blend in with most architectural design. For instance, the doors would not work well with Victorian-style inspired homes. They are, however, common among conventional houses where steal panels and other metals are used in decorating the house.
Also, one cannot really play well with colors on the doors. Usually, homeowners have to settle with the metallic look. This doesn't say that the natural aluminum surface is not good. In fact it is. However, for people who are fond of playing with colors, the doors may not be the best choice.
Another drawback to using the doors is that they tend to catch the atmosphere of large kitchens since they are usually associated with the kitchen doors of most restaurants. But again, this may not be as bad at all since many people actually love to create a certain atmosphere in their kitchen that may only be contributed to metals.
A change of look is what a sliding door could give when used in residential homes. In the industrial settings however, they have become the mainstay.