Extruded Aluminum Sliding Door Track Guide

Aluminum is one of the most used metals in today’s society – Extruded Aluminum Sliding Door Track in Guide  it can be found across a number of industries, such as construction and commercial, and in a number of applications, such as beverage cans and appliances. When choosing a manufacturer of aluminium extrusion for supplying the metal that you use in your workplace, however, it is important that you carefully consider which one will be best for your needs.

Aluminium Window Frames Catalogue

The manufacturer will begin by removing the aluminium from deep within the earth’s crust (either as bauxite ore or feldspar). Often, the Bayer’s method, Wohler’s method or Hall Heroult method is chosen to remove the metal in its molten form. It is then hardened and moulded into whatever shape the manufacturer desires. When the aluminium is extracted from the earth in its solid form, Aluminium Structural Framing it will be passed through a number of mechanical processes that are designed to give the metal its desired shape. These processes include: rolling, drawing, forging, spinning, piercing and extrusion.

Aluminium Windows Cape Town

Regardless of whether aluminium has been found in its molten or solid form, the manufacturer will then pass it through either a hot working or cold working process to prepare it for their customers. When using the hot working process (the most popular of the two), a billet will be heated to a temperature of over 79 degrees Celsius, which will allow the aluminium to be easily distorted and placed into its desired shape.

Aluminium Window Frames Catalogue

The reason for the popularity of the hot working process over the cold working one can be fully realized when you compare aluminium extrusion to squeezing toothpaste out of its tube. It is much easier to extrude the metal when it is malleable, meaning that it must have been heated to a certain temperature.

Finally, the aluminium will pass through an extrusion and drawing process that runs almost parallel to each other. This is the final step in the whole extrusion process and is the step that gives the metal its entire shape. Deep drawing, for example, is used give the metal a cup, conical tapered, cylinder and seamless tube shape. For less curved shapes, Aluminum Cabinet Extrusions the drawing process is skipped.

Alspec Aluminium Catalogue

Once you are satisfied with the processes and methods utilized by a potential manufacturer of aluminium extrusions, you can begin submitting your orders with them. If, after your first delivery, you are still satisfied with the manufacturer based on the promptness of the order being filled and the quality of the aluminium that you receive, you can continue the relationship.

Extruded Aluminum Sliding Door Track in Guide?

Aluminium Windows Cape Town

In our past articles I talked about all the steps required to properly replace your old wood sash windows with energy efficient vinyl windows. I told you how to measure for the new windows. Then we discussed the removal of the wood sashes and parting bead. Finally, I told you how to install, seal, and trim the vinyl replacement windows. But, what if those old windows in your home are made of aluminum instead of wood? Is the process the same? No, it's not the same at all. So, the next few articles are going to explain the differences between replacing wood windows versus aluminum windows.

When discussing the proper frame style for replacing the wood sash windows, I explained the difference between new construction frames versus replacement frames. When replacing aluminum windows, there is another option we have to consider regarding frame style. It's called a "retrofit" frame. Let's go over each frame type. First, we have the new construction frame with the nailing fin. If you choose to go this route, you have to remove the exterior around each window opening, pull out the nails holding the aluminum window to the studs, nail in the new vinyl window, apply flashing, caulk, and re-install the exterior around each window.(I get tired just talking about it!)In addition to being a whole lot of labor, you can run into major problems trying to install the exterior product around each window opening. If your home has stucco, you have to try and match the rest of the stucco. It can be done, but not by you. Even most professional stucco guys can't get a perfect match. What if you have wood siding? Well, you can cut away 2" of the siding around each window to get to the nail fin, then you can apply 1 X 2 or 1 X 3 trim around each window. Certainly not as much work as the stucco home, but probably more work than the average homeowner cares to tackle. What if each window is surrounded by brick? Let's not even go there! You would have to remove the bricks, then re-install them all when finished.

Trust me, you don't want to replace your old aluminum windows with new construction vinyl windows. You want to use either the replacement frame like the one used to replace the wood sash windows, or something called a retrofit frame, that is popular in the west where stucco is a common exterior. Since the procedure for measuring is the same regardless of the frame style chosen, this article will discuss the proper measuring procedure, and future articles will explain the difference in the installation process for replacement versus retrofit.

If you look at the portion of the aluminum frame that goes around the window opening into your surrounding walls, you will see three separate "legs" that form two pockets. The outside leg and the center leg form the first pocket. Your screen and stationary panel will be in this pocket. The center leg and inside leg form the second pocket, and your sliding panel is in that pocket. Find the "leg" that is the widest on all four sides. When measuring the width, run your tape measure from the widest leg on the left to the widest leg on the right. This should be the narrowest measurement. Then, subtract 3/8" from that measurement. This is the width of the replacement window. Measure the height the same way. When measuring the height, measure as close to the center of the window as possible. This is especially important on windows wider than six feet, because the top wood header has a tendency to sag over time, making the center of the opening the narrowest. You don't need to deduct 3/8" from the height like you did on the width. 1/4" is fine. These are the dimensions you use when ordering your vinyl window. If you have any picture windows(windows without a vent panel), there will only be two legs and one pocket. You still measure the same way.

Next week I will discuss whether your home is a candidate for retrofit frames or replacement frames...

Where Are Aluminium Doors Best Installed?

Aluminium Windows Cape Town

While aluminium is a very versatile material and aluminium doors can be suitably installed in a variety of indoor and outdoor contexts, two of the best places for the installation of aluminium doors are in industrial locations and as barriers between the inside and outside.

Aluminium doors are ideally suited to being installed as a barrier between indoor and outdoor environments because of their weatherproof and durable nature. This makes them a top choice for patio doors and café or bar doors leading to courtyards. Aluminium is one of best materials for patio door frames because the metal is a strong and very low-maintenance product. The advantages of installing aluminium framed doors as barriers between in and outdoors are largely due to the natural properties of the metal which make it resistant to corrosion as well as being impermeable and odourless. The aluminium framed doors do not rust and provide premium stability if installed correctly. Not only do doors of aluminium come in an extensive range of powder coated colours, they can also be carefully patterned for various aesthetic effects. Finally, aluminium framed doors are one of the best doors to be installed between interior and exterior because they won't warp or swell in damp conditions as wooden doors often do.

One of the second locations where doors of aluminium are best installed is in the heavy duty contexts of factories and warehouses where they are often the number one choice for a variety of applications. The popularity of aluminium doors in these environments is due again to the naturally strong, durable and low-maintenance nature of the metal. Aluminium is able to withstand any of the bumps and scrapes that are customary during the movement and transport of industrial machinery and products. Doors for industrial locations are made from large, high-strength metal panels that withstand the passage of oversize cargo and bulky machinery. Another reason why aluminium doors are such a top choice for heavy duty purposes is because the metal can be thermally treated to be scratch and dent resistant.

These are just too of the most popular locations for aluminium framed doors, but really, with such a versatile metal, the possible applications are endless. As well as providing a practical patio door and industrial door solution, glass and aluminium doors can be used inside the home in bathrooms and bedrooms as well as in the interiors or offices and other commercial constructions.

Aluminium Window Frames For Sale

https://ferngully.co.za/list/

Fern Gully Have Aluminum Track Channel List

Extruded Aluminum Sliding Door Track Reviews

Aluminum is one of the most used metals in today’s society – Extruded Aluminum Sliding Door Track in Reviews  it can be found across a number of industries, such as construction and commercial, and in a number of applications, such as beverage cans and appliances. When choosing a manufacturer of aluminium extrusion for supplying the metal that you use in your workplace, however, it is important that you carefully consider which one will be best for your needs.

Aluminium Sections Catalogue

The manufacturer will begin by removing the aluminium from deep within the earth’s crust (either as bauxite ore or feldspar). Often, the Bayer’s method, Wohler’s method or Hall Heroult method is chosen to remove the metal in its molten form. It is then hardened and moulded into whatever shape the manufacturer desires. When the aluminium is extracted from the earth in its solid form, Aluminum Extrusions Retail it will be passed through a number of mechanical processes that are designed to give the metal its desired shape. These processes include: rolling, drawing, forging, spinning, piercing and extrusion.

Aluminium Windows Cape Town

Regardless of whether aluminium has been found in its molten or solid form, the manufacturer will then pass it through either a hot working or cold working process to prepare it for their customers. When using the hot working process (the most popular of the two), a billet will be heated to a temperature of over 79 degrees Celsius, which will allow the aluminium to be easily distorted and placed into its desired shape.

Aluminium Window Frames For Sale

The reason for the popularity of the hot working process over the cold working one can be fully realized when you compare aluminium extrusion to squeezing toothpaste out of its tube. It is much easier to extrude the metal when it is malleable, meaning that it must have been heated to a certain temperature.

Finally, the aluminium will pass through an extrusion and drawing process that runs almost parallel to each other. This is the final step in the whole extrusion process and is the step that gives the metal its entire shape. Deep drawing, for example, is used give the metal a cup, conical tapered, cylinder and seamless tube shape. For less curved shapes, Aluminum Cabinet Extrusions the drawing process is skipped.

Aluminium Window Frames For Sale

Once you are satisfied with the processes and methods utilized by a potential manufacturer of aluminium extrusions, you can begin submitting your orders with them. If, after your first delivery, you are still satisfied with the manufacturer based on the promptness of the order being filled and the quality of the aluminium that you receive, you can continue the relationship.

Extruded Aluminum Sliding Door Track in Reviews?

Aluminium Windows

Greenhouse kit frames may be made of galvanized steel pipe, aluminum, plastic or wood. It is very important when considering purchasing a greenhouse to look at the type of frame it is constructed of. There are also many different grades of these materials used. With the steel pipe frame you not only have to consider the size of the tubing, but also the spacing of the tubing. Naturally, closer spacing of the bows will result in a stronger frame. This is also true of aluminum frames. The thickness of the aluminum, the spacing and the extra supports will all determine the strength. What type of wood is being used is very important also.

Typically the prices going from low to high will be as follows.

1. Plastic frames
2. Lightweight Aluminum Frames
3. Pipe Frames
4. Wood Frames
5. Heavy Duty Aluminum Frames

Some of these such as the wood frames will require maintenance to keep up. The rest of the frame types are typically maintenance free.

Many consumers simply look at size, shape and price and do not consider that at some point they will probably want to add some accessories such as circulating fans, ventilation systems, hanging heaters, misting or fogging systems, etc. to their greenhouse. With plastic frames it is virtually impossible to add any accessories without building a frame to mount the accessories to. Many times these frames simply are not heavy enough to support even a hanging basket. Usually with wood and pipe frames the strength is there, but you will still need to do some extra framing out to mount the accessories. There are also some lighter weight aluminum frame greenhouse kits which will require additional framing to mount your accessories. Most quality aluminum framed greenhouses will offer a channel where bolts will slide to the exact location you desire to put your accessories. Usually this type of frame will even make it possible to add a wire shelf above your benches for extra space.

These are all just general guidelines. It is best to investigate each greenhouse kit on an individual basis.

How to Fix an Aluminum Sliding Door

Aluminium Window Frames Details

In our past articles I talked about all the steps required to properly replace your old wood sash windows with energy efficient vinyl windows. I told you how to measure for the new windows. Then we discussed the removal of the wood sashes and parting bead. Finally, I told you how to install, seal, and trim the vinyl replacement windows. But, what if those old windows in your home are made of aluminum instead of wood? Is the process the same? No, it's not the same at all. So, the next few articles are going to explain the differences between replacing wood windows versus aluminum windows.

When discussing the proper frame style for replacing the wood sash windows, I explained the difference between new construction frames versus replacement frames. When replacing aluminum windows, there is another option we have to consider regarding frame style. It's called a "retrofit" frame. Let's go over each frame type. First, we have the new construction frame with the nailing fin. If you choose to go this route, you have to remove the exterior around each window opening, pull out the nails holding the aluminum window to the studs, nail in the new vinyl window, apply flashing, caulk, and re-install the exterior around each window.(I get tired just talking about it!)In addition to being a whole lot of labor, you can run into major problems trying to install the exterior product around each window opening. If your home has stucco, you have to try and match the rest of the stucco. It can be done, but not by you. Even most professional stucco guys can't get a perfect match. What if you have wood siding? Well, you can cut away 2" of the siding around each window to get to the nail fin, then you can apply 1 X 2 or 1 X 3 trim around each window. Certainly not as much work as the stucco home, but probably more work than the average homeowner cares to tackle. What if each window is surrounded by brick? Let's not even go there! You would have to remove the bricks, then re-install them all when finished.

Trust me, you don't want to replace your old aluminum windows with new construction vinyl windows. You want to use either the replacement frame like the one used to replace the wood sash windows, or something called a retrofit frame, that is popular in the west where stucco is a common exterior. Since the procedure for measuring is the same regardless of the frame style chosen, this article will discuss the proper measuring procedure, and future articles will explain the difference in the installation process for replacement versus retrofit.

If you look at the portion of the aluminum frame that goes around the window opening into your surrounding walls, you will see three separate "legs" that form two pockets. The outside leg and the center leg form the first pocket. Your screen and stationary panel will be in this pocket. The center leg and inside leg form the second pocket, and your sliding panel is in that pocket. Find the "leg" that is the widest on all four sides. When measuring the width, run your tape measure from the widest leg on the left to the widest leg on the right. This should be the narrowest measurement. Then, subtract 3/8" from that measurement. This is the width of the replacement window. Measure the height the same way. When measuring the height, measure as close to the center of the window as possible. This is especially important on windows wider than six feet, because the top wood header has a tendency to sag over time, making the center of the opening the narrowest. You don't need to deduct 3/8" from the height like you did on the width. 1/4" is fine. These are the dimensions you use when ordering your vinyl window. If you have any picture windows(windows without a vent panel), there will only be two legs and one pocket. You still measure the same way.

Next week I will discuss whether your home is a candidate for retrofit frames or replacement frames...

Alspec Aluminium Catalogue

https://ferngully.co.za/list/

Fern Gully Have Aluminum Track Channel List

Extruded Aluminum Sliding Door Track South Africa

Aluminum is one of the most used metals in today’s society – Extruded Aluminum Sliding Door Track in South Africa  it can be found across a number of industries, such as construction and commercial, and in a number of applications, such as beverage cans and appliances. When choosing a manufacturer of aluminium extrusion for supplying the metal that you use in your workplace, however, it is important that you carefully consider which one will be best for your needs.

Aluminium Sections Catalogue

The manufacturer will begin by removing the aluminium from deep within the earth’s crust (either as bauxite ore or feldspar). Often, the Bayer’s method, Wohler’s method or Hall Heroult method is chosen to remove the metal in its molten form. It is then hardened and moulded into whatever shape the manufacturer desires. When the aluminium is extracted from the earth in its solid form, Aluminum Cabinet Extrusions it will be passed through a number of mechanical processes that are designed to give the metal its desired shape. These processes include: rolling, drawing, forging, spinning, piercing and extrusion.

Aluminium Window Sections Catalogue

Regardless of whether aluminium has been found in its molten or solid form, the manufacturer will then pass it through either a hot working or cold working process to prepare it for their customers. When using the hot working process (the most popular of the two), a billet will be heated to a temperature of over 79 degrees Celsius, which will allow the aluminium to be easily distorted and placed into its desired shape.

Aluminium Window Frames For Sale

The reason for the popularity of the hot working process over the cold working one can be fully realized when you compare aluminium extrusion to squeezing toothpaste out of its tube. It is much easier to extrude the metal when it is malleable, meaning that it must have been heated to a certain temperature.

Finally, the aluminium will pass through an extrusion and drawing process that runs almost parallel to each other. This is the final step in the whole extrusion process and is the step that gives the metal its entire shape. Deep drawing, for example, is used give the metal a cup, conical tapered, cylinder and seamless tube shape. For less curved shapes, Aluminium Window Frame Extrusions the drawing process is skipped.

Aluminium Windows

Once you are satisfied with the processes and methods utilized by a potential manufacturer of aluminium extrusions, you can begin submitting your orders with them. If, after your first delivery, you are still satisfied with the manufacturer based on the promptness of the order being filled and the quality of the aluminium that you receive, you can continue the relationship.

Extruded Aluminum Sliding Door Track in South Africa?

Aluminium Windows

If you want durability, low maintenance and weather resistance, aluminum railings are just the right metal for you. Look out for the best manufacturers, wholesalers or distributors who can match up your expectations.

Aluminum railings have a long list of benefits to offer for your homes. For all custom applications aluminum is the best metal to be used. Impact resistance, color retention and weather ability in any environment are the best features of aluminum railings you can find. They can be a perfect complement for a decorative porch or deck.

The aluminum railings can achieve any kind of shape to match your home decorations. Aluminum will not rust especially when they are power coated offer long lasting finish with superior protection against the elements and do not splinter or crack. So you need not have to get it painted after every few years unlike steel.

Aluminum railings have minimal shrinkage and expansion characteristics and remain consistent throughout extreme heating and cooling temperatures. If you are considering for other options like wood then you will have to get it treated with pesticides or chemicals. They even splinter or fail completely at times causing injury. Aluminum railings on the other side eliminate all these and let you have a friendly environment eliminating all your health concerns.

There are many aluminum railings Surrey manufacturers in the market who can even create one of your own deck styles by mixing aluminum balusters with another material. For example, it can be combined with wooden or bamboo rails to create an exotic ambience. Amongst numerous other ones, underneath are some significant characteristics of aluminum deck and porch railings and its complements or benefits:

- Interior and exterior guardrails and handrails.

- Clear or encased functional glass, aluminum pickets, aluminum convention panels, or cable cord for infill section options:

  • ADA compliant catch rails
  • Steel embeds and hefty measure components & for strength
  • Tempered glass for security & influence resistance
  • Tough, powder-coated finishes for better climate opposition and hue retention.
  • Water corrosion: Special coatings for opposition to saline water.

Manufacture of Aluminum railings offers every combination of furniture and deck railings to distinguish your deck from others and have the ability to be included in almost all styles.

Scrap Aluminum Grades - How to Sort and Clean Scrap Aluminum to Maximize Its Value

Alspec Aluminium Catalogue

Metal fabrication equipment is used in important facets of the manufacturing industry. It serves the structural steel industry very well as it helps in other metal fabricating industries. Producers of this equipment have clients ranging from small and medium size enterprises to iron and fabricating shops and large construction companies.

The most common types of metal fabrication equipment include hydraulic press brakes, pinch rolls, plate shears, bending machines, tube benders and plate rolls. All these machines will help the entire workload easier. Look into the features of these types of equipment.

Hydraulic press brakes

Hydraulic press brakes are created to deliver the kind of ease and comfort an operator is looking for in the product. They are equipped with a ram system to provide maximum efficiency on operator control. Down stroking ram systems are favored over up stroking systems because they lessen operator fatigue. The system with a thick ram makes it easier to move in between extra heavy frames. Alongside with this component, a steel torsion is also utilized. At times, the hydraulic press brake contains limit switches and overload protection systems. Speeds of the press brakes are adjustable and controllable as well.

Hydraulic shears

This is yet another type of metal fabrication equipment used in order to make the job of individuals easier. Looking for those with foot pedals and emergency stops is highly favorable for the company. Programmable axes may help control blade gaps, stroke length, back gauge and shearing times. At times, the shears are also commendable for its capacity to transfer balls and load metal sheets. It also possesses a full protection guard system. Shears are used in order to provide smooth and quiet operation while cutting or manufacturing metal parts.

Plate bending machines

Plate bending machines vary according to specifications of the particular industry making use of this industrial product. There are goods that are best suited for small to medium production requirement for pipes, angles, flats and tubes. Ornamental and job shops will surely favor this type of bending machine. There are plate bending machines that are versatile enough with hydraulic forming features. This is commendable in industries were pipe, tube and aluminum extrusion bending is required.

There are other types of metal fabrication equipment sold by a lot of manufacturers. At times, this equipment may be available from second hand machine stores. What matters is that the machine will work for the particular manufacturing process it has to serve.

Aluminium Window Frames Details

 


https://ferngully.co.za/list/

Fern Gully Have Aluminum Track Channel List

Extruded Aluminum Sliding Door Track Johannesburg

Aluminum is one of the most used metals in today’s society – Extruded Aluminum Sliding Door Track in Johannesburg  it can be found across a number of industries, such as construction and commercial, and in a number of applications, such as beverage cans and appliances. When choosing a manufacturer of aluminium extrusion for supplying the metal that you use in your workplace, however, it is important that you carefully consider which one will be best for your needs.

Aluminium Windows Pretoria

The manufacturer will begin by removing the aluminium from deep within the earth’s crust (either as bauxite ore or feldspar). Often, the Bayer’s method, Wohler’s method or Hall Heroult method is chosen to remove the metal in its molten form. It is then hardened and moulded into whatever shape the manufacturer desires. When the aluminium is extracted from the earth in its solid form, Aluminum Framing System it will be passed through a number of mechanical processes that are designed to give the metal its desired shape. These processes include: rolling, drawing, forging, spinning, piercing and extrusion.

Aluminium Window Frames Catalogue

Regardless of whether aluminium has been found in its molten or solid form, the manufacturer will then pass it through either a hot working or cold working process to prepare it for their customers. When using the hot working process (the most popular of the two), a billet will be heated to a temperature of over 79 degrees Celsius, which will allow the aluminium to be easily distorted and placed into its desired shape.

Aluminium Window Frames Catalogue

The reason for the popularity of the hot working process over the cold working one can be fully realized when you compare aluminium extrusion to squeezing toothpaste out of its tube. It is much easier to extrude the metal when it is malleable, meaning that it must have been heated to a certain temperature.

Finally, the aluminium will pass through an extrusion and drawing process that runs almost parallel to each other. This is the final step in the whole extrusion process and is the step that gives the metal its entire shape. Deep drawing, for example, is used give the metal a cup, conical tapered, cylinder and seamless tube shape. For less curved shapes, Aluminum Cabinet Frame Extrusions the drawing process is skipped.

Aluminium Sections Catalogue

Once you are satisfied with the processes and methods utilized by a potential manufacturer of aluminium extrusions, you can begin submitting your orders with them. If, after your first delivery, you are still satisfied with the manufacturer based on the promptness of the order being filled and the quality of the aluminium that you receive, you can continue the relationship.

Extruded Aluminum Sliding Door Track in Johannesburg?

Aluminium Window Frames Details

Porch Railings - First And Lasting Impression

The porch railing is the first thing your visitors sees and in order that it makes a lasting impression, this article gives you tips for porch railings. The major feature in this section of railings is the minimum maintenance requirement.

The Form And Look - Essence Of Porch Railing

Since the porch is the first thing, a visitor observes after getting down from the car it always makes a lasting impression on the visitor. Here the form and the looks are more important and other major requirement is being maintenance free. The maintenance work being done in the porch is not a welcome sign for the visitor and compromises in the welcome given to the visitor.

Materials Used In Porch Railings

Materials have to be carefully selected for porch railings, workability is more important since the form, and looks are more important here. Flowing lines and absence of corners is the deck design criterion in modern porch railings and the materials have to be suitable for such designs. Most common materials are,

  1. Stainless Steel: Because of high workability and the fact that it maintains shine for a long time and that too in adverse conditions, stainless steel is the preferred material in porch railings. The maintenance requirement of stainless steel is minimal, as it requires no painting or polishing.
  2. PVC coated steel: The steel can be coated with PVC in multiple colors. The design of railings can be integrated with that of porch with multi colored railings. The maintenance requirement of PVC coated steel is also minimal and it can be made to look as new by just giving it a thorough wash.
  3. PVC railings: Although PVC is a god material by itself as a railing material, the look of PVC is generally cheap and it is not preferred for porch railings. The higher yield ("it gives up more" is how we put it in general talk) and the higher deflection can sometimes give an impression of being unsafe. Therefore, it is not used as material for porch railing.
  4. Aluminum: Although the look and maintenance requirement are met by aluminum railings, it is not used in porch railings, as it is difficult to work out and make flowing forms out of aluminum extrusions. Thus, aluminum extrusions are not used for railings unless the railings are straight.
Make your choice of material porch railings and make a good first impression on your visitor and it sure will last for a long time.

Replacing Aluminum Frame Single Pane Windows

Alspec Aluminium Catalogue

Porch Railings - First And Lasting Impression

The porch railing is the first thing your visitors sees and in order that it makes a lasting impression, this article gives you tips for porch railings. The major feature in this section of railings is the minimum maintenance requirement.

The Form And Look - Essence Of Porch Railing

Since the porch is the first thing, a visitor observes after getting down from the car it always makes a lasting impression on the visitor. Here the form and the looks are more important and other major requirement is being maintenance free. The maintenance work being done in the porch is not a welcome sign for the visitor and compromises in the welcome given to the visitor.

Materials Used In Porch Railings

Materials have to be carefully selected for porch railings, workability is more important since the form, and looks are more important here. Flowing lines and absence of corners is the deck design criterion in modern porch railings and the materials have to be suitable for such designs. Most common materials are,

  1. Stainless Steel: Because of high workability and the fact that it maintains shine for a long time and that too in adverse conditions, stainless steel is the preferred material in porch railings. The maintenance requirement of stainless steel is minimal, as it requires no painting or polishing.
  2. PVC coated steel: The steel can be coated with PVC in multiple colors. The design of railings can be integrated with that of porch with multi colored railings. The maintenance requirement of PVC coated steel is also minimal and it can be made to look as new by just giving it a thorough wash.
  3. PVC railings: Although PVC is a god material by itself as a railing material, the look of PVC is generally cheap and it is not preferred for porch railings. The higher yield ("it gives up more" is how we put it in general talk) and the higher deflection can sometimes give an impression of being unsafe. Therefore, it is not used as material for porch railing.
  4. Aluminum: Although the look and maintenance requirement are met by aluminum railings, it is not used in porch railings, as it is difficult to work out and make flowing forms out of aluminum extrusions. Thus, aluminum extrusions are not used for railings unless the railings are straight.
Make your choice of material porch railings and make a good first impression on your visitor and it sure will last for a long time. Alspec Aluminium Catalogue

 


https://ferngully.co.za/list/

Fern Gully Have Aluminum Track Channel List