Aluminium Frame Section Guide

Aluminum is one of the most used metals in today’s society – Aluminium Frame Section in Guide  it can be found across a number of industries, such as construction and commercial, and in a number of applications, such as beverage cans and appliances. When choosing a manufacturer of aluminium extrusion for supplying the metal that you use in your workplace, however, it is important that you carefully consider which one will be best for your needs.

Aluminium Window Frames Details

The manufacturer will begin by removing the aluminium from deep within the earth’s crust (either as bauxite ore or feldspar). Often, the Bayer’s method, Wohler’s method or Hall Heroult method is chosen to remove the metal in its molten form. It is then hardened and moulded into whatever shape the manufacturer desires. When the aluminium is extracted from the earth in its solid form, Aluminum Extrusion Rail it will be passed through a number of mechanical processes that are designed to give the metal its desired shape. These processes include: rolling, drawing, forging, spinning, piercing and extrusion.

Aluminium Windows Cape Town

Regardless of whether aluminium has been found in its molten or solid form, the manufacturer will then pass it through either a hot working or cold working process to prepare it for their customers. When using the hot working process (the most popular of the two), a billet will be heated to a temperature of over 79 degrees Celsius, which will allow the aluminium to be easily distorted and placed into its desired shape.

Aluminium Windows South Africa

The reason for the popularity of the hot working process over the cold working one can be fully realized when you compare aluminium extrusion to squeezing toothpaste out of its tube. It is much easier to extrude the metal when it is malleable, meaning that it must have been heated to a certain temperature.

Finally, the aluminium will pass through an extrusion and drawing process that runs almost parallel to each other. This is the final step in the whole extrusion process and is the step that gives the metal its entire shape. Deep drawing, for example, is used give the metal a cup, conical tapered, cylinder and seamless tube shape. For less curved shapes, Aluminum Extrusions South Africa the drawing process is skipped.

Aluminium Windows Cape Town

Once you are satisfied with the processes and methods utilized by a potential manufacturer of aluminium extrusions, you can begin submitting your orders with them. If, after your first delivery, you are still satisfied with the manufacturer based on the promptness of the order being filled and the quality of the aluminium that you receive, you can continue the relationship.

Aluminium Frame Section in Guide?

Alspec Aluminium Catalogue

The proper placement of doors and windows is essential in a house for the good light and ventilation. So, what would be better than having the option of aluminium doors and windows? The correct ventilation not only provides you with fresh air but keeps the house cool and cuts down the electricity bills, to a certain extent. There are many other green and eco friendly materials for this purpose, but they don't give a good appealing view. Aluminium, on the other hand, has all these qualities and looks appealing to the eye also. They are super efficient, strong, light weight and cheap too. It also has other qualities like it can withstand many harsh factors like the chemicals, heat, corrosion, etc.

The other advantage of the aluminium doors and windows is that they are available in a huge range of shapes, designs, sizes and with different color finishes. The finishes include matte, solid, shiny, etc. You can also get it personalized paint finishes or faux finishes of your own choice. There is an option of the danmer customized doors windows and shutters. They are available in the form of the sliding doors, fixed windows, and many more. These would improve the indoor of your house.

These doors and windows consume far less space than the traditional ones made of iron or wood. This can be a boon in case you have less space at your place. Therefore, you can fit more and more things in a small area with the help of the aluminium doors and windows.

The other factor that makes it different from others is that these windows and doors are very easy to install and only require a bit of information. They are eco friendly and can be recycled. If combined with fiberglass or the plastic glass, then it could be the most intelligent thing one can do. It is the best combination which is attractive and low maintenance for the long run.

The doors and windows made of aluminium are extremely useful and can be recycled. It has many advantages over the wooden or the iron windows. So, the best option for your house is to have the proper symmetry and matching of the windows and doors which would make your house beautiful.

Important Things You Should Know About Bifold Doors

Aluminium Window Frames Details

High strength aluminium alloys.

The origin of aluminium alloys in aircraft construction started with the first practical all-metal aircraft in 1915 made by Junkers in Germany, of materials said to be `iron and steel'. Steel presented the advantages of a high modulus of elasticity, high proof stress and high tensile strength. Unfortunately these were accompanied by a high specific gravity, almost three times that of the aluminium alloys and about ten times that of plywood. Aircraft designers during the 1930s were therefore forced to use steel in its thinnest forms. To ensure stability against buckling of the thin plate, intricate shapes for spar sections were devised.

In 1909 Alfred Wilm, in Germany, accidentally discovered that an aluminium alloy containing 3.5 per cent copper, 0.5 per cent magnesium and silicon and iron, as unintended impurities, spontaneously hardened after quenching from about 480°C. The patent rights of this material were acquired by Durener Metallwerke who marketed the alloy under the name Duralumin. For half a century this alloy has been used in the wrought heat-treated, naturally aged condition. The improvements in these properties produced by artificial ageing at a raised temperature of, for example, 175°C, were not exploited in the aircraft industry until about 1934.

In addition to the development of duralumin (first used as a main structural material by Junkers in 1917) three other causes contributed to the replacement of steel by aluminium alloys. These were a better understanding of the process of heat treatment, the introduction of extrusions in a wide range of sections and the use of pure aluminium cladding to provide greater resistance to corrosion. By 1938, three groups of aluminium alloys dominated the field of aircraft construction and, in fact, they retain their importance to the present day. The groups are separated by virtue of their chemical composition, to which they owe their capacity for strengthening under heat treatment.

The first group is contained under the general name duralumin having a typical composition of: 4 per cent copper, 0.5 per cent magnesium, 0.5 per cent manganese, 0.3 per cent silicon, 0.2 per cent iron, with the remainder aluminium. The naturally aged version was covered by Air Ministry Specification DTD 18 issued in 1924, while artificially aged duralumin came under Specification DTD 111 in 1929. DTD 111 provided for slight reductions in 0.1 per cent proof stress and tensile strength.

The second group of aluminium alloys differs from duralumin chiefly by the introduction of 1 to 2 per cent of nickel, a high content of magnesium and possible variations in the amounts of copper, silicon and iron. `Y' alloy, the oldest member of the group, has a typical composition of. 4 per cent copper, 2 per cent nickel, 1.5 cent magnesium, the remainder being aluminium and was covered by Specification DTD 58A issued in 1927. Its most important property was its retention of strength at high temperatures, which meant that it was a particularly suitable material for aero engine pistons. Its use in airframe construction has been of a limited nature only. Research by Rolls-Royce and development by High Duty Alloys Ltd produced the `RR' series of alloys. Based on Y alloy, the RR alloys had some of the nickel replaced by iron and the copper reduced. One of the earliest of these alloys, RR56 had approximately half of the 2 per cent nickel replaced by iron, the copper content reduced from 4 to 2 per cent, and was used for forgings and extrusions in aero engines and airframes.

The third and latest group depends upon the inclusion of zinc and magnesium and their high strength. Covered by Specification DTD 363 issued in 1937, these alloys had a nominal composition: 2.5 per cent copper, 5 per cent zinc, 3 per cent magnesium and up to 1 per cent nickel. In modern versions of this alloy nickel has been eliminated and provision made for the addition of chromium and further amounts of manganese.

Aircraft structural aluminium.

Of the three basic structural materials, namely wood, steel and aluminium alloy, only wood is no longer of significance except in laminates for non-structural bulkheads, floorings and furnishings. Most modern aircraft still rely on modified forms of the high strength aerospace aluminium alloys which were introduced during the early part of the 20th century. Steels are used where high strength, high stiffness and wear resistance are required. Other materials, such as titanium and fibre-reinforced composites first used about 1950, are finding expanding uses in airframe construction.

Aluminium Window Sections Catalogue

https://ferngully.co.za/johannesburg/

Fern Gully Have Aluminium Section List

Aluminium Frame Section Recommended

Aluminum is one of the most used metals in today’s society – Aluminium Frame Section in Recommended  it can be found across a number of industries, such as construction and commercial, and in a number of applications, such as beverage cans and appliances. When choosing a manufacturer of aluminium extrusion for supplying the metal that you use in your workplace, however, it is important that you carefully consider which one will be best for your needs.

Aluminium Windows Cape Town

The manufacturer will begin by removing the aluminium from deep within the earth’s crust (either as bauxite ore or feldspar). Often, the Bayer’s method, Wohler’s method or Hall Heroult method is chosen to remove the metal in its molten form. It is then hardened and moulded into whatever shape the manufacturer desires. When the aluminium is extracted from the earth in its solid form, Aluminum Extrusions South Africa it will be passed through a number of mechanical processes that are designed to give the metal its desired shape. These processes include: rolling, drawing, forging, spinning, piercing and extrusion.

Aluminium Windows South Africa

Regardless of whether aluminium has been found in its molten or solid form, the manufacturer will then pass it through either a hot working or cold working process to prepare it for their customers. When using the hot working process (the most popular of the two), a billet will be heated to a temperature of over 79 degrees Celsius, which will allow the aluminium to be easily distorted and placed into its desired shape.

Aluminium Window Frames Details

The reason for the popularity of the hot working process over the cold working one can be fully realized when you compare aluminium extrusion to squeezing toothpaste out of its tube. It is much easier to extrude the metal when it is malleable, meaning that it must have been heated to a certain temperature.

Finally, the aluminium will pass through an extrusion and drawing process that runs almost parallel to each other. This is the final step in the whole extrusion process and is the step that gives the metal its entire shape. Deep drawing, for example, is used give the metal a cup, conical tapered, cylinder and seamless tube shape. For less curved shapes, Aluminum Cabinet Frame Extrusions the drawing process is skipped.

Alspec Aluminium Catalogue

Once you are satisfied with the processes and methods utilized by a potential manufacturer of aluminium extrusions, you can begin submitting your orders with them. If, after your first delivery, you are still satisfied with the manufacturer based on the promptness of the order being filled and the quality of the aluminium that you receive, you can continue the relationship.

Aluminium Frame Section in Recommended?

Aluminium Windows

Glass doors are a great choice for both homes and businesses, and offer a great many advantages. In this article I'm going to look at specifically what those advantages are, as well as covering possible disadvantages which you should be aware of.

One of the most obvious and appealing benefits of doors made from glass is the fact that they allow light to pass through. For doors which open to the outside there is the benefit of being able to enjoy natural sunlight entering the room. Not only does this sunlight look and feel much more pleasant than artificial light, but it also helps to reduce the need for that artificial lighting, lowering costs as well as representing a greener alternative.

But even in cases where the door is not an exterior one, a glass door still allows light to pass from one room to the other, not only creating a visually more attractive space, but also a more practical one, since there are fewer shadows and darker areas, maximising the efficient use of the room.

One of the possible disadvantages of course with glass is that it does not usually permit privacy. Clearly this is why very few bathrooms have doors made from glass! But there is a way in which you can enjoy the benefits of a glass door being able to allow light to pass through it whilst also enjoying a certain amount of privacy. Frosted glass, or even coloured opaque glass can be used for both partitions and doors to create an attractive feature which also provides the privacy required.

Another benefit of glass as a material for use in doors and partitions is that it is incredibly durable and extremely easy to keep clean. Glass does not rust, or corrode, it is not susceptible to woodworm, and it doesn't collect dust. All that is necessary to keep the glass door or glass partition looking clean and attractive is to give it an occasional wipe with a cloth and some glass cleaner. This is ideal for both businesses and homes.

One of the disadvantages of glass doors is that they are more liable to crack or break if they receive a very sharp knock or heavy blow. However, such a blow would probably cause significant damage to any door, and as they're made of toughened glass, glass doors and partitions are more than tough enough to cope with everyday use, and should not shatter or break revealing sharp edges should a seriously hard knock cause any damage.

Modern digital printing now also enables glass doors to be patterned or to have designs added. This is less useful for homes, but for businesses and commercial properties it provides the opportunity to have company logos or other relevant information included on the glass.

With a choice of colours and many different types of frameless glass doors, including fixed, hinged, sliding and folding systems, there are many benefits worth considering, both for the home and for business environments.

Solid Security Glass Block Windows & Walls For Commercial, Architectural and Institutional Projects

Aluminium Window Sections Catalogue

In our past articles I talked about all the steps required to properly replace your old wood sash windows with energy efficient vinyl windows. I told you how to measure for the new windows. Then we discussed the removal of the wood sashes and parting bead. Finally, I told you how to install, seal, and trim the vinyl replacement windows. But, what if those old windows in your home are made of aluminum instead of wood? Is the process the same? No, it's not the same at all. So, the next few articles are going to explain the differences between replacing wood windows versus aluminum windows.

When discussing the proper frame style for replacing the wood sash windows, I explained the difference between new construction frames versus replacement frames. When replacing aluminum windows, there is another option we have to consider regarding frame style. It's called a "retrofit" frame. Let's go over each frame type. First, we have the new construction frame with the nailing fin. If you choose to go this route, you have to remove the exterior around each window opening, pull out the nails holding the aluminum window to the studs, nail in the new vinyl window, apply flashing, caulk, and re-install the exterior around each window.(I get tired just talking about it!)In addition to being a whole lot of labor, you can run into major problems trying to install the exterior product around each window opening. If your home has stucco, you have to try and match the rest of the stucco. It can be done, but not by you. Even most professional stucco guys can't get a perfect match. What if you have wood siding? Well, you can cut away 2" of the siding around each window to get to the nail fin, then you can apply 1 X 2 or 1 X 3 trim around each window. Certainly not as much work as the stucco home, but probably more work than the average homeowner cares to tackle. What if each window is surrounded by brick? Let's not even go there! You would have to remove the bricks, then re-install them all when finished.

Trust me, you don't want to replace your old aluminum windows with new construction vinyl windows. You want to use either the replacement frame like the one used to replace the wood sash windows, or something called a retrofit frame, that is popular in the west where stucco is a common exterior. Since the procedure for measuring is the same regardless of the frame style chosen, this article will discuss the proper measuring procedure, and future articles will explain the difference in the installation process for replacement versus retrofit.

If you look at the portion of the aluminum frame that goes around the window opening into your surrounding walls, you will see three separate "legs" that form two pockets. The outside leg and the center leg form the first pocket. Your screen and stationary panel will be in this pocket. The center leg and inside leg form the second pocket, and your sliding panel is in that pocket. Find the "leg" that is the widest on all four sides. When measuring the width, run your tape measure from the widest leg on the left to the widest leg on the right. This should be the narrowest measurement. Then, subtract 3/8" from that measurement. This is the width of the replacement window. Measure the height the same way. When measuring the height, measure as close to the center of the window as possible. This is especially important on windows wider than six feet, because the top wood header has a tendency to sag over time, making the center of the opening the narrowest. You don't need to deduct 3/8" from the height like you did on the width. 1/4" is fine. These are the dimensions you use when ordering your vinyl window. If you have any picture windows(windows without a vent panel), there will only be two legs and one pocket. You still measure the same way.

Next week I will discuss whether your home is a candidate for retrofit frames or replacement frames...

Aluminium Window Frames For Sale

https://ferngully.co.za/johannesburg/

Fern Gully Have Aluminium Section List

Aluminium Frame Section South Africa

Aluminum is one of the most used metals in today’s society – Aluminium Frame Section in South Africa  it can be found across a number of industries, such as construction and commercial, and in a number of applications, such as beverage cans and appliances. When choosing a manufacturer of aluminium extrusion for supplying the metal that you use in your workplace, however, it is important that you carefully consider which one will be best for your needs.

Aluminium Windows Cape Town

The manufacturer will begin by removing the aluminium from deep within the earth’s crust (either as bauxite ore or feldspar). Often, the Bayer’s method, Wohler’s method or Hall Heroult method is chosen to remove the metal in its molten form. It is then hardened and moulded into whatever shape the manufacturer desires. When the aluminium is extracted from the earth in its solid form, Buy Aluminum Extrusion it will be passed through a number of mechanical processes that are designed to give the metal its desired shape. These processes include: rolling, drawing, forging, spinning, piercing and extrusion.

Aluminium Window Frames For Sale

Regardless of whether aluminium has been found in its molten or solid form, the manufacturer will then pass it through either a hot working or cold working process to prepare it for their customers. When using the hot working process (the most popular of the two), a billet will be heated to a temperature of over 79 degrees Celsius, which will allow the aluminium to be easily distorted and placed into its desired shape.

Aluminium Windows

The reason for the popularity of the hot working process over the cold working one can be fully realized when you compare aluminium extrusion to squeezing toothpaste out of its tube. It is much easier to extrude the metal when it is malleable, meaning that it must have been heated to a certain temperature.

Finally, the aluminium will pass through an extrusion and drawing process that runs almost parallel to each other. This is the final step in the whole extrusion process and is the step that gives the metal its entire shape. Deep drawing, for example, is used give the metal a cup, conical tapered, cylinder and seamless tube shape. For less curved shapes, Aluminum Extrusion Rail the drawing process is skipped.

Aluminium Window Frames For Sale

Once you are satisfied with the processes and methods utilized by a potential manufacturer of aluminium extrusions, you can begin submitting your orders with them. If, after your first delivery, you are still satisfied with the manufacturer based on the promptness of the order being filled and the quality of the aluminium that you receive, you can continue the relationship.

Aluminium Frame Section in South Africa?

Aluminium Windows Pretoria

Having lived with all three types of windows and patio doors in the past three years, I feel that I am an 'expert user' when it comes to opening and closing in each medium: wood, pvc and aluminium.

First, the novice's choice: wood. It looks great, feels warm, can be stained a medium or dark shade or painted any colour of the spectrum. It's an age-old medium so what can go wrong? The main problems are humidity and strong sunlight.

There are varying qualities of wood on offer, depending on your budget. A moderately-priced pair of French doors on a south-facing house wall suffered a degree of warping, creating gaps that had to be plugged each winter in an attempt to keep the cold draughts at bay whereas, in warmer damp circumstances, the door had to be forcibly pushed and pulled back into its aperture.

Two good summers and the four coats of varnish had virtually vapourised, revealing cracking wood that needed nourishing and protecting from the next couple of years' weather.

Second, the double-glazing salesman's special offer: PVC. Overpriced by a couple of well-known companies who then discount by 50% if you hesitate, PVC is also available in varying qualities. At the higher end of the market, the frames are often reinforced with metal.

Generally with more features than wooden doors and windows, PVC should not require much more than a quick wipe with a damp cloth for the first few years and its looks are therefore easier to maintain. We have some PVC French Doors from the lower price range. As value for money, they are quite good but an element of trust is lacking in terms of defence against determined intruders. They feel floppy and flimsy when opening and closing and there's a knack to locking and unlocking them successfully. We have older PVC doors from the higher price range and, whilst more sturdy (reinforced with metal) they are looking a tad ratty.

The PVC windows screeched with wind whistling through, like semi-detached tinnitus.

Thirdly and finally, the long term investment: powder-coated aluminium frames. If you are fed up with sanding down wooden frames and considering the easy option of PVC or coated aluminium, particularly for a wide opening with multi-folding doors. Consider whether PVC is up to the task of substituting for the wall of your house.

Stand back and look through closed doors at the difference between PVC and aluminium - it is very noticeable. With PVC, there are windows of scenery between wide areas of plastic (two frames together might measure between 8 and 10 inches, 20 to 25cms) so the doors block up to 20 per cent of the potential view and light-source.
 
Aluminium frames on bifolding doors from manufacturer SunSeeker Doors, being stronger, are only about 2 inches or 5 centimeters. The profile is also considerably smaller so the doors use far less space than PVC or wood when folded back. For those who want color, several options are available to order, the most popular (after standard white) are: Grey, blue, green, brown and silver. Aluminium Frames are more expensive than cheap PVC or wood but prices are comparable with the better quality PVC doors. Is aluminum worth the extra cost? If you want the "wow" factor, strength, longevity, maximum living space and the most panoramic view,Yes.

How Custom Bi-Fold Doors Can Help You Save Space

Aluminium Window Sections Catalogue

Over the last several years, heavy-weight particle board and cabinet-based displays have lost their appeal and made way for the next innovation in displays systems - truss display systems. Today, exhibitors who want a display that looks substantial without the cost and assembly headache of cabinetry are choosing truss systems.

The Problem

Display systems that use materials such as cabinets and laminate panels to create larger island displays can cost exhibitors thousands in shipping and assembly costs alone for each show. On top of that, constant assembly and tear-down of these systems can leave them chipped, scratched and beat-up after just a few years.

The Solution

Today, while laminate panel systems are still widely used and requested, a new breed of aluminum frame displays can be a less-costly alternative. These systems are sleek, functional, and offer all of the amenities of laminate panel systems, including shelving, overhead lighting, and storage. Additionally, these systems offer versatile and striking visual options including backlit graphics, tension fabric graphics and areas for plasma screens and computer demos.

How They Can Maximize Your Budget

As an alternative to heavier wood displays, aluminum displays are much lighter in weight, making them far less costly to ship. Additionally, many aluminum frame displays assemble without the need for tools, saving money in set-up costs.

Aluminium Windows

 


https://ferngully.co.za/johannesburg/

Fern Gully Have Aluminium Section List

Aluminium Frame Section Sandton

Aluminum is one of the most used metals in today’s society – Aluminium Frame Section in Sandton  it can be found across a number of industries, such as construction and commercial, and in a number of applications, such as beverage cans and appliances. When choosing a manufacturer of aluminium extrusion for supplying the metal that you use in your workplace, however, it is important that you carefully consider which one will be best for your needs.

Alspec Aluminium Catalogue

The manufacturer will begin by removing the aluminium from deep within the earth’s crust (either as bauxite ore or feldspar). Often, the Bayer’s method, Wohler’s method or Hall Heroult method is chosen to remove the metal in its molten form. It is then hardened and moulded into whatever shape the manufacturer desires. When the aluminium is extracted from the earth in its solid form, Where To Buy Aluminum Extrusion it will be passed through a number of mechanical processes that are designed to give the metal its desired shape. These processes include: rolling, drawing, forging, spinning, piercing and extrusion.

Alspec Aluminium Catalogue

Regardless of whether aluminium has been found in its molten or solid form, the manufacturer will then pass it through either a hot working or cold working process to prepare it for their customers. When using the hot working process (the most popular of the two), a billet will be heated to a temperature of over 79 degrees Celsius, which will allow the aluminium to be easily distorted and placed into its desired shape.

Aluminium Windows

The reason for the popularity of the hot working process over the cold working one can be fully realized when you compare aluminium extrusion to squeezing toothpaste out of its tube. It is much easier to extrude the metal when it is malleable, meaning that it must have been heated to a certain temperature.

Finally, the aluminium will pass through an extrusion and drawing process that runs almost parallel to each other. This is the final step in the whole extrusion process and is the step that gives the metal its entire shape. Deep drawing, for example, is used give the metal a cup, conical tapered, cylinder and seamless tube shape. For less curved shapes, Where To Buy Aluminum Extrusion the drawing process is skipped.

Alspec Aluminium Catalogue

Once you are satisfied with the processes and methods utilized by a potential manufacturer of aluminium extrusions, you can begin submitting your orders with them. If, after your first delivery, you are still satisfied with the manufacturer based on the promptness of the order being filled and the quality of the aluminium that you receive, you can continue the relationship.

Aluminium Frame Section in Sandton?

Aluminium Window Frames For Sale

Extrusion is the process to change the structure and shape of different metals. Some of the metals that are commonly extruded include aluminium, copper, lead, magnesium, zinc, titanium etc.

As aluminium is malleable in nature, it is easy to extrude. Specific dies are used for the aluminium extrusion process. These steel dies have opening of the desired shapes. Primarily, this process can be of two types - hot and cold. For hot process, precise heating is very important. It is done above the aluminium's recrystallization temperature. While, cold process is done at room temperature or near room temperature.

To obtain superior quality and improved surface finished aluminium extrusions, accurate temperate and its monitoring is vital. The finishing increases the durability, strength and its appearance. In the process, a billet is heated at the temperature of 400 C to 500 C and is pushed through the die under pressure to create preferred profiles. The shape, structure and specifications vary according to the requirements of the product, customers and its application.

The company's manufacturing aluminium extrusions prefer extrusion process over welding as it gives product with constant cross section. The strength and lightweight (strength-to-weight ratio) of this metal makes it popular among customers. Its several other properties gives it edge over other metals. These are cost-effective, corrosion-resistive, flexible and durable.

The prime source of aluminium is bauxite ore and Feldspar to some extent. Some of the fields where the this metal's extruded shapes are used include transportation, building and construction to name a few.

Replacing Aluminum Frame Single Pane Windows

Alspec Aluminium Catalogue

"We can't stop the thugs in this neighborhood from breaking out, shooting out, and vandalizing these expensive insulated glass windows we put in the school just last year," the maintenance supervisor said. "Do you have a solution that can stop our cycle of throwing good money after bad?" he said. Unfortunately this is not an unfamiliar concern with owners, managers, and maintenance supervisors of commercial buildings, schools, courthouses, and transit authorities.

How can you stop this cycle of spending, time loss, and frustration? Consider solid glass block window and walls. In this article you'll learn:

1. Why architects and building owners use high security glass masonry units
2. Where to use solid blocks and glass bricks.
3. Options and accessories in security blocks and bricks.

Why architects and building owners use high security glass masonry units

The cheapest way to put up a glass window or wall in a commercial, architectural, or institutional project is with a standard single pane or insulated glass system constructed generally with a vinyl or aluminum framing system. However if your business or facility is located where graffiti, vandalism, bullets, bad weather, noise, or fire are a concern the lowest initial cost window or wall system may not be the answer for achieve the best life cycle costs. The Vistabrik line of solid security glass blocks from Pittsburgh Corning may be what you're searching for. Some reasons building owners have chosen this line of blocks include:

Bullet resistant- These blocks are UL tested and made of 3" thick glass to resist penetration from high impact weapons including 9 mm and .357 magnum bullets.

Reduce vandalism and graffiti - With "non-stick" glass surfaces graffiti is easier to remove and forcible entry is difficult since 8" x 8" x 3" blocks weigh 40 lbs. per square foot mortared together.

Fire resistant - When a higher level of building safety and fire resistance are desired without having to look at ugly wires in the glass, solid glass blocks are a preferred choice. Window panels can be designed with 45, 60, and 90 minute UL approved fire ratings.

Noise reduction - Buildings near train stations, large crowds, traffic, and machinery can be hard to lease and suffer from poor employee productivity. Solid glass bricks have a Sound Transmission Class of 53 and a noise reduction coefficient of .05 resulting in quieter interior spaces.

Cut maintenance costs - Solid glass masonry units can reduce total costs of ownership if you select this durable, hard to break block at the initial stages of the building project - thereby saving ongoing maintenance costs of repair and replacing glass windows and walls.

Where to use solid blocks and glass bricks

Here are some places where solid glass blocks have been used most frequently in commercial, institutional and architectural projects:

Gymnasiums and recreation facilities - one installation is Lloyd Hall in Philadelphia Pennsylvania.

Elevated walkways and parking garages - (check out the walkway at Perry High School in Pittsburgh Pennsylvania and parking garage at Logan Airport in Boston Massachusetts).

Glass block stairwells, shelters, and walls in transit stations, jails, detention centers, courthouses, police stations, and embassies - Solid glass units provide security without giving up light and looks. Some interesting installations include Yankee Stadium Complex for the New York City Transit Authority and the Clay County Detention Center in Liberty Missouri.

Glass block windows in factories and manufacturing buildings - A building owner in Columbus Ohio is planning to use solid glass bricks to replace insulated glass aluminum framed windows that have been getting broken and shot out.

Options and Accessories in Security Blocks and Bricks

If you're looking for a clear view window or wall or need higher privacy, then the selection of solid glass blocks is for you. For a high clarity look there are 8" x 8" x 3", 4" x 8" x 3" and 3" x 8" x 3" sizes available. For higher privacy projects the 8" x 8" x 3" size can be supplied with a stippled face.

The solid blocks are generally mortared together with galvanized panel reinforcing through the horizontal mortar joints (usually every 24") and panel anchors (every 24" as well) to tie the window panels into the jambs or sides of the opening. These glass masonry units also meet tempered glass windows standards due to their strength.

Conclusion

Keeping building costs and security and safety concerns down has never been as important as it is today in our unstable world. Using solid security glass block windows and walls can be one step to provide building owners, employees, and parents with increased comfort, style, security and most importantly - peace of mind.

Aluminium Windows

 


https://ferngully.co.za/johannesburg/

Fern Gully Have Aluminium Section List